Handyman For Ceiling Fan Installation – Introduction The ceiling fan improves cooling in summer and heating in winter. The result: You’ll feel more comfortable while saving on utility bills. And it’s easy to assemble yourself, thanks to new, stronger suspension systems and electronic controls. We’ll show you how to avoid common mistakes when installing yourself.
You don’t have to be a Casablanca fan to appreciate the elegance a ceiling fan can bring to your home. You can enjoy the fan all year round as it creates a welcome breeze in the summer and circulates warm air in the winter.
Handyman For Ceiling Fan Installation
Installing a ceiling fan (technically known as “paddle fans”) can be frustrating, to say the least. Specialized suspension systems are poorly developed or non-existent so you have to wing it most of the time. These days, many manufacturers have designed versatile fan mounting systems that take the hassle out of ceiling fan installation. When you add improved, stronger ceiling boxes, you’ll find that any ceiling fan can raise any ceiling, sloped or flat, quickly and easily.
Ceiling Fan Installation Service Makes It Easier; Here’s Why!
In this article, we describe quite clear instructions that go beyond the basic kit with the propeller. We’ll also show you how to avoid common mistakes like putting parts in the wrong order and forgetting to move the lids ahead of time. Few mistakes are more serious than these. Standard electrical boxes or low-hanging blades can be dangerous.
Besides the fan, you can purchase accessories like a ceiling fan remote, luxury lighting packages, and custom furniture paddles.
If all goes well, you can install the ceiling fan within a couple of hours, including the cleaning process. In most cases, the entire job only requires a hammer and a 3/8-inch screwdriver. Nut driver and wire stripper.
Most of the time, the wires that fed the previous ceiling fan wiring light fixture will be sufficient to connect the new fan. If you have a ceiling fan wiring arrangement other than ours and are not familiar with wiring techniques, contact an electrician or building inspector for assistance.
Ceiling Fan Installation & Repair Services In Newark, Nj
The steps here apply to more than 95 percent of all fans. There may be slight differences, especially when it comes to light and blade combinations, so you’ll still need to refer to the instructions that came with your fan.
Manufacturers generally require the fan blades to be at least 7 feet above the ground. Since most propeller and motor kits are less than 12 inches long, they fit into a standard 8-footer. Roof with appropriate clearance.
Angled roofs require the installation of “down bars” (also called extension tubes or down tubes) that lower the motor and fan blades so that they clear the sloping roof surface. The more space between the ceiling and the fan, the better. A fan contains a larger volume of air, and the closer the blades are to you, the more air movement you will experience.
Most fans come with a short bottom bar designed for an 8-foot installation. Ceilings. If your ceiling is less than 8 feet, you will need to remove the attached rod and install the fan. But if you have a high or sloping ceiling, buy a longer lower bar.
Who To Hire To Install Or Repair Your Ceiling Fan
Determine the roof slope by pressing 2 ft. Level against the ceiling and measure the vertical distance from the level to the ceiling. Divide this number by 2 to get a drop of more than 12 inches on a horizontal track, slope of 3/12. Refer to the chart below to determine the minimum bottom bar length for your desired blade diameter.
Turn off the power to the main board and remove the light module. Pound the electrical box outside the frame with a hammer and wood, then pull the electrical cable out of the old box and through the roof vent. Leave the old ceiling fan junction box in the ceiling cavity if you cannot easily remove it through the hole.
Tip: Before you blow up the box, bend back the plastic clips or loosen the metal cable clamps so that it is easier to pull out the electrical cable after dismantling the box.
Insert the fan bracket into the hole, place the flat edge of the foot on the ceiling, and center the shaft over the hole. If your ceiling is thicker than 1/2 inch, like ours, rotate the feet and place the rod at the depth of the box from the ceiling. Rotate the shaft to secure the bracket to the frame. Install the metal belt on the post so that it is centered over the hole.
Who To Hire To Install A Ceiling Fan
The ends of the post fit into the roof and end screws insert into the joints as the post rotates.
Before starting any work, turn off the circuit breaker supplying the switch and lighting fixture. If the device has a working light, turn it on. Then you know you have the right breaker when the light goes off. Check the wires with a voltage tester to ensure the wires are disconnected after removing the fixture and turning on the wall switch.
The next step is to remove the existing plastic or metal electrical box and install a “fan bracket” designed to hold ceiling fans. There are few traditional boxes that are strong enough to support a ceiling fan, so don’t think about hanging your fan in an existing box. Instead, purchase a fan bracket when purchasing your fan.
If the frame is accessible from the attic or if the construction is new, you can choose brackets that are installed with nails. Otherwise, choose a mount designed to slide across the sunroof and electrical box. These brackets adjust to fit between the framing members of your roof; You rotate the shaft to secure it to the frame.
Ceiling Fan Installation & Replacement
Most electrical boxes on the frame are easy to screw and hammer into the wood (Image 2). After releasing the cable, leave the old box in the recess (Photo 3) without squeezing the box through the sunroof. Then pull the cable through the hole, slide the fan bracket through the hole and install it following the instructions included with the bracket. The small feet on the ends of the brackets maintain the proper distance from the back of 1/2 inch. Thick ceilings so that the new electrical box is flush with the roof.
Feed the existing wire through the cable clamp on top of the new metal ceiling fan junction box, then slide the box over the harness bolts and tighten the nuts to secure the box to the pole using a nut driver or deep socket. Crimp a loop of ground wire three-quarters of the way around the ground screw and tighten the screw.
Position the suspension bracket so that the hole in the bracket faces the top side of the sloped ceiling. Then screw it into the box using the special screws provided with the fan bracket.
Pull the ceiling fan wires into the new box, mount the box on the bracket (Photo 4) and attach the fan hanging bracket (Photo 5).
Ceiling Fan Installation In Littleton, Colorado
Place the motor right side up, pass the wire through the lower rod and insert the lower rod into the mounting collar.
Pass the lower bar pin through the collar and tube, lock it with the cotter pin and tighten the bolts and lock nuts.
Slide the collar cover, then the canopy over the bottom rail. Slide the ball onto the lower rail and push the pin through both sets of holes, then lift the ball onto the pin and tighten the mounting screw.
Lift the assembly over the open side of the rack and lower it into place. Rotate the motor until the ball slot locks onto the tab on the bracket. Includes assembly instructions for your fan. Pictures 6-9 will help you with several basic steps.
How Much For Fan Install With No Fixture, And Is This Handyman Or Electrician Job?
Here’s what you need to know about ceiling fan wire colors: Connect the bare ground wire from the box to the green ground wire on the bracket using a wire connector. Connect the white neutral wire from the motor to the neutral wire from the box. Connect the blue and black wire from the motor to the black hot wire from the box and fold it neatly inside the box.
Attach the fan blades to their brackets and attach the brackets to the bottom of the motor. It is easiest to tighten the screw in the holder with a screwdriver while lifting the blade assembly into place. Then drive the screw.
Place the radio receiver into the switch housing/light pod assembly and connect the light pod wires according to the manufacturer’s instructions. Note the settings on the receiver icon switch so you can dial in the same settings as the electronic controls on the wall switch. Now loosen the screws on the switch housing axis by half. Connect the motor ceiling fan wires to the socket on the receiver and screw the switch housing into the hub. Tighten the screws.
Check the switches on the wall-mounted electronic switch and reset them (if necessary).